How To Install A Tub Surround To Studs

March 22, 2020

Once it is in place have a helper with you to hold it firmly as you drill pilot holes through the flange where it meets the center of the studs. Then go across the top at each of the studs.

How To Install A Bathtub Install An Acrylic Tub And Tub Surround Diy

Nextile direct to stud alcove bathtub surround install directions.

How to install a tub surround to studs. Fasten the drywall strips to the studs with 1¼-inch-long decking screws. Before installing the tub add the new drain shoe while its still easy to get at Figure B. If so install the remaining panel before turning to the front wall panel.

Step by step full install. To attach the enclosure to the studs use a 38-inch bit to drill pilot holes through the flange. Some kits have two side wall panels.

Lay a thick ring of clear silicone caulk under the rim and screw it together following the tub manufacturers instructions. Now the problem is I cant glue it directly over the stud because of the plastic. Drill pilot holes in the panel flanges where they meet the studs and screw or nail the panel to the wall.

However my bath tub is located on a wet wall outside wall. Step by step full install - YouTube. Install the Plumbing Panels.

Caulk the tub to the surround and secure the surround to the studs. If playback doesnt begin shortly try restarting your device. Herein how do you install a tub surround to studs.

Fill the spaces above the tub surround with moisture-resistant drywall. With this type of tub surround drywall or trim pieces will likely have to be added over the lip to cover it up. I have purchased this AquaGlass Divani tub surround which provides for direct over stud mounting.

At the tub measure from the reference line to the center of the spout pipe. To attach the enclosure to the studs use a 38-inch bit to drill pilot holes through the flange. Thicker sturdier tub surround panels are usually attached direct-to-studs.

Then go across the top at each of the studs. Fasten the enclosure at each stud with 1 12-inch self-tapping washer head screws or galvanized roofing nails. This means you will have to remove the drywall around the tub surround so the lip of the surround panels can be screwed right into the studs.

Once your drywall is cut work your way from back to front. Step-by-step installation procedure for Lyons Victory Nested Tub and Elite Wall Surround. Next use a drill to screw the surround into each wall stud.

Conceal the seams in the drywall with joint compound and drywall tape. Please note that this video was produced to go hand-in-hand with. Then carefully set the surround on top of the silicone caulk.

Take careful measurements dry fit your shower surround to ensure the right fit and then install. This Old House plumbing and heating expert Richard Trethewey updates a bath. A bathtub and shower combo is a great addition to your bathroom and installing a direct-to-stud shower surround is a project that you can complete in under one day.

Youll want to start with the back wall panel setting it in place and leveling it with the tub. These surrounds are made of acrylic and the panels are attached to the walls with special adhesivesIf you are installing a tub surround and you need to cut holes for the faucet and spout or trim it to fit the space around your tub make sure you cut it carefully to avoid chipping or damaging the tub surround. Fasten the enclosure at each stud with 1 ½-inch self-tapping washer head screws or galvanized.

Do this on the vertical side flange 8 inches on center. I had to put up insulation and a sheet of plastic around the tub area to protect from moisture. Then measure from the top of the tub to the center of the spout pipe and do the same with the faucet.

Level the panel and make sure it sits flush against the lip of the tub or shower pan. Then install the bathtub and anchor it to the wall studs. See below for a shopping list and toolsSUBSCRIBE to This Old House.

Place a bead of silicone caulk around the entire perimeter of the tub on the ledge next to the flange. Do this on the vertical side flange 8 inches on center.

Diy Bathroom Remodeling Phase 1 How To Install A New Bathtub