How To Replace Bathtub Faucet Valve

July 22, 2019

300 to 2700. 15 minutes to 1 hour.

How To Fix A Leaking Bathtub Faucet Diy Family Handyman

Adjust the tailpipe according to the holes and connections.

How to replace bathtub faucet valve. The set screw may be in the back like the faucet or at the very top of the handle. Place a socket wrench over the bathtub faucet stem until it covers the hex nut. You may need to slip a putty knife between the base of the faucet and tub deck if its been caulked or sealed.

Its a good idea to flush the new faucet and check for leaks before youre done. The valve mechanism varies according to the brand and model of the faucet. Remove the new faucet from the packaging.

With a bucket handy use an adjustable wrench to loosen and remove the flexible extension from the faucet. Unscrew any remaining elements at the base of the faucet with your screwdriver. Seal the edge with a thin layer of bathroom caulk.

You will not know what kind of stem you need prior to taking the faucet apart so do not buy it. Learn how to easily replace a two-handle faucet with this straight forward step-by-step video tutorial from Delta Faucet. You may need a faucet handle puller if the handle will not come off by hand.

Check all the connections and retighten if needed. Shower socket wrench for wall-type Teflon tape. Using the appropriate faucet valve socket wrench set you should be able to remove the bathtub faucet valve.

Place the rubber or plastic gasket or gaskets as provided so it will fit between the faucet and the top of the sink holes. Turn the wrench counterclockwise to loosen the nut until you can pull the stem free. Slot in the new bathtub faucet valve and re-install the mounting bolts.

Wiggle the handle and pull it off. After this re-install the faucet handles and test whether the replacement has been successful. A faulty diverter in your spout will affect the efficiency of your shower.

To conclude replacing a bathtub faucet is not a difficult task. Repeat this same process with the handles. Unscrew the whole stem from pipes.

Change out the old Teflon tape with new tape around the shower arm wrapping it tightly to avoid any slow drips. There should be a valve on each one one for hot and one for cold. Turn both of these valves off by twisting them clockwise as though they were faucets.

Remove the stem out of the faucet with caution. Once done attach the new shower head by twisting it in a clockwise direction. Under the sink you will see two supply lines coming out of the wall and going up to your faucet.

Start by shutting off the wall valves and turning on the faucet to drain down residual pressure. When the faucet is accurately positioned at its place and pipe connections are at their respective holes insert the washer and tighten the nuts with hands first and then with the wrench. Repeat the steps if you have a two-handle system.

Pick the new faucet and place it over the holes of the sink where you placed the gasket. Then run hot and cold water for one minute. Replacing your tubs spout is the easiest way to solve this problem.

Test the shower head by turning on the water. Using a valve stem wrench or channel locks remove the stem. Put the new faucet in position placing the appropriate valves into their matching holes.

Drain the remaining water into the bucket. Stabilize the valve assembly with a pair of slotted pliers as you loosen the water line. Now you should disconnect the entire stem from the bathtubs water pipes.

Replace the aerator and youre done installing your new bathroom faucet. Turn off the water to the faucet. Just remove the aerator.

With a bucket and towel handy for any residual water use an adjustable wrench to remove the supply lines. Next remove the flexible line from the shutoff valve. Bring this part to your local hardware or plumbing supply store to buy a replacement.

How To Change A Bathtub Faucet 14 Steps Wikihow